GNSS Simulator
Talk to an engineer
GNSS Simulator

Free engineering tool · 04

GNSS Doppler Shift Calculator

Calculate carrier frequency shift from radial relative speed, or convert a Doppler offset to equivalent radial velocity. Choose a GNSS carrier preset or enter a custom RF frequency.

Speed ↔ frequency shift GPS · Galileo · BeiDou · GLONASS Signed results + wavelength

Convert radial motion and Doppler

Calculations run in your browser.

Nominal carrier: 1575.420000 MHz

Sign convention: positive speed means approaching; negative means receding. Frequency shift is received minus nominal carrier frequency. Positive shift means a higher received frequency.

Use the relative velocity component along the satellite–receiver line of sight. Total vehicle speed or satellite orbital speed is not automatically the radial speed.

LOAD AN ARITHMETIC EXAMPLE

Doppler estimate

Ready
Estimated Doppler shift
— Hz

Nominal carrier
—
Carrier wavelength
—
Received frequency shift
—
Radial approach speed
—
Geometric range rate
—
Motion-only received carrier
—
Shift per 1 m/s approach
—
Fractional frequency shift
—

Enter the carrier and motion settings, then calculate.

First-order, one-way RF carrier model for speeds much smaller than c. Results describe geometric radial motion; clock drift, atmospheric effects and receiver-specific sign conventions require separate handling.

Compare Doppler shift across GNSS carriers

Calculate to compare the same radial approach speed at different nominal carrier frequencies.

Carrier preset Nominal MHz Wavelength (m) Motion-only shift (Hz)
Calculate to compare carriers.

The comparison covers the fixed-frequency presets. The selected GLONASS FDMA channel or custom carrier is shown in the main result.

GNSS Doppler shift and radial velocity formulas

Let v be signed approach speed, f₀ the nominal carrier frequency, Δf the received frequency shift and ρ̇ the geometric range rate. With this convention, approaching motion gives v > 0 and ρ̇ < 0.

c = 299,792,458 m/s
Wavelength: λ = c / f₀
Frequency shift: Δf ≈ f₀ × v / c = −ρ̇ / λ
Equivalent approach speed: v ≈ c × Δf / f₀
Geometric range rate: ρ̇ = −v
Motion-only received carrier: f_received ≈ f₀ + Δf

Use radial relative speed

Project the relative satellite–receiver velocity onto the line of sight. Receiver ground speed alone does not define a satellite signal’s Doppler shift.

Keep carrier and shift separate

Enter the RF carrier in the carrier field and its signed offset in Hz or kHz. An IF center frequency is not a replacement for the original RF carrier when converting motion to RF Doppler.

Use a one-way model

This calculation follows a satellite-to-receiver signal path. It does not apply the factor of two used for a monostatic radar round trip.

Worked GPS L1 Doppler example

At the GPS L1 nominal carrier of 1575.42 MHz, a relative approach speed of +100 m/s produces approximately +525.504 Hz of carrier shift in this model. The wavelength is approximately 0.190294 m.

Δf ≈ 1,575,420,000 × 100 / 299,792,458
   ≈ +525.504 Hz
Geometric range rate = −100 m/s
Motion-only received carrier ≈ 1,575,420,525.504 Hz

Changing the speed to −100 m/s reverses the shift to approximately −525.504 Hz. These are arithmetic examples, not predictions for a particular satellite pass.

GNSS Doppler calculation questions

What does a positive Doppler shift mean here?

A positive shift means the received carrier is higher than the nominal carrier. In this calculator, positive radial approach speed means the transmitter and receiver are getting closer. Geometric range rate uses the opposite sign. Check your receiver or processing software documentation before importing a signed Doppler observation.

Can a stationary GNSS receiver still observe Doppler?

Yes. A stationary receiver can observe Doppler because the satellite is moving relative to it. The input is relative radial speed along the line of sight, including the motion of both endpoints, rather than receiver speed alone.

Can I enter vehicle speed or satellite orbital speed directly?

Only if that value is already the relative radial component along the signal path. Otherwise project the relative velocity onto the line of sight first. This tool does not calculate satellite positions or a time-varying pass from ephemerides.

Does Doppler-to-speed conversion recover actual receiver velocity?

It gives an equivalent radial speed under the motion-only model. Real GNSS measurements can also contain receiver and satellite clock drift, oscillator offsets and other effects. One satellite Doppler value does not determine a complete three-dimensional receiver velocity.

Why do GLONASS G1 and G2 need a channel number?

Legacy GLONASS FDMA carriers depend on frequency channel k. This tool accepts integer channels from -7 to +6 and uses G1 = 1602 + 0.5625k MHz or G2 = 1246 + 0.4375k MHz. These presets are for the FDMA signal plan, not every GLONASS CDMA signal.

Should I multiply the result by two for GNSS?

No. The GNSS satellite-to-receiver link is one way. The factor of two in the common monostatic radar Doppler formula describes an outgoing-and-returning reflection path and is not used here.

Connect the estimate to a GNSS test

Scroll to Top