GNSS ENGINEERING TOOLS · GEOMETRY DEMO
GNSS Skyplot & DOP Calculator
Create a skyplot from supplied satellite azimuth and elevation angles. Adjust the elevation mask or enable individual satellites to explore GDOP, PDOP, HDOP, VDOP and TDOP under an unweighted single-clock model.
Geometry results
All DOP values are dimensionless. No measured position error, metre-valued accuracy or timing error in seconds is calculated.
Satellite skyplot
North is up; azimuth increases clockwise, with east at the right. Radius is proportional to zenith angle: center = 90° elevation, outer ring = 0°. The dashed circle is the mask boundary. IDs are labeled for up to 16 input satellites where space permits; use the table for the full list and overlapping points.
Satellite selection and line-of-sight vectors
Toggle Enabled to update the CSV and recalculate. A checked satellite below the mask is still excluded from DOP.
| Enabled | ID | Azimuth · deg | Elevation · deg | Selection | LOS East | LOS North | LOS Up |
|---|
Model and numerical checks
| Item | Result |
|---|
Input format and conventions
| Column | Accepted input |
|---|---|
| id | Unique 1–12 character ID, starting with a letter; letters, digits, underscores and hyphens |
| azimuth_deg | 0–360° clockwise from local north; 360° is normalized to 0° |
| elevation_deg | 0–90° above the local horizon |
| use | Optional: 1/true to enable, 0/false to disable; all enabled when omitted |
Headers are trimmed and case-insensitive. IDs are converted to uppercase. Additional columns are rejected. Limit: 64 satellites, 64 KiB and 8 CSV columns. Invalid fields or repeated IDs stop calculation; disabled rows must also contain valid directions.
Geometry and DOP equations
N = cos(el) × cos(az)
U = sin(el)
G row = [−E, −N, −U, 1]
Q = (GᵀG)⁻¹
VDOP = √qUU
PDOP = √(qEE + qNN + qUU)
TDOP = √qbb
GDOP = √(qEE + qNN + qUU + qbb)
The clock state b is a range-equivalent clock bias. This is an unweighted, four-state geometry model with independent equal-variance range errors. No signal-quality or elevation weighting is applied.
Why a DOP value may be unavailable
At least four selected satellites and numerical rank four are required. Equal-elevation or other dependent directions can leave position and clock components inseparable even when the satellite count is four or more.
The solver uses column-pivoted Householder QR. This tool withholds DOP if the triangular factor's 1-norm condition exceeds 100000000. This is a numerical display policy, not a GNSS receiver acceptance threshold or an accuracy rating.
Repeated directions under different IDs are retained and reported. Verify one row per distinct satellite: repeating the same observation under new labels can make DOP look artificially favorable.
Formula reference: ESA Navipedia: Positioning Error.
Skyplot and DOP FAQ
Does this show live or predicted satellites?
No. The tool plots the azimuth and elevation values you supply. It does not download ephemerides, use your location or predict satellite visibility. All presets are synthetic examples. Use directions for the same observer, local reference frame and epoch.
Which DOP model is used?
The calculation uses equal weights and four states: East, North, Up and one common receiver-clock bias expressed in range units. It assumes independent equal-variance range errors. Satellite IDs do not add constellation-specific clock or inter-system bias states. No signal-quality weighting is applied.
Why can four or more satellites still have no DOP result?
Satellite count alone does not ensure independent geometry. Rank-deficient directions cannot separate all four states. The tool also withholds DOP when the QR triangular factor condition exceeds its numerical display limit of 100000000. Unavailable DOP is not reported as zero.
Are satellites exactly on the elevation mask included?
Yes. An enabled satellite is used when its elevation is greater than or equal to the mask. The slider uses whole-degree steps from 0 to 90 degrees. Disabled satellites remain excluded regardless of elevation. Selection checkboxes update the use column in the CSV.
Does HDOP or TDOP give actual accuracy?
No. DOP is a dimensionless geometry factor under the stated model. This tool does not calculate measured position error, metre-valued accuracy, confidence bounds or clock error in seconds. Receiver noise, bias, correlations, corrections and the estimator model also affect real results.
Are inputs uploaded, and what does the report contain?
All parsing, plotting and calculations run locally in your browser without an external calculation library or data request. The CSV report includes normalized directions, enabled flags, mask selections, line-of-sight vectors, model status and available DOP values. It describes your supplied geometry, not verified satellite positions.
Compare geometry with measured receiver results
Record the selected satellites and error-model assumptions alongside reference-based position and timing measurements.